PartsTable
Technical Data Sheet
Download PDF

3633128 — CLAMP,LOOP

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

3633128: CLAMP,LOOP.

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.422 INCHES MINIMUM AND 0.454 INCHES MAXIMUM IN, material: STEEL COMP 1010 BAND, overall_width: 1.000 INCHES NOMINAL IN, style_designator: CENTER MOUNT, tongue_hole_type: ROUND, UNTHREADED, material_thickness: 0.111 INCHES MINIMUM AND 0.141 INCHES MAXIMUM IN. This part is cataloged in the U.S.

Government catalog under NSN 5340-00-741-2995, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
3633128
NSN: 5340-00-741-2995
FSC: 5340 — Hardware, Commercial
CAGE: 23862 — MILITARY VEHICLES OPN GENERAL MOTORS TRUCK AND BUS GROUP MS 2603-02 (USA)
SPECIFICATIONS
diameter0.422 INCHES MINIMUM AND 0.454 INCHES MAXIMUM IN
materialSTEEL COMP 1010 BAND
overall_width1.000 INCHES NOMINAL IN
style_designatorCENTER MOUNT
tongue_hole_typeROUND, UNTHREADED
material_thickness0.111 INCHES MINIMUM AND 0.141 INCHES MAXIMUM IN
loop_inside_diameter2.500 INCHES NOMINAL IN
material_document_and_classificationASTMA108 ASSN STD SINGLE MATERIAL RESPONSE BAND
distance_from_loop_center_to_tongue_end2.375 INCHES NOMINAL IN
distance_from_loop_center_to_short_tongue_end2.265 INCHES NOMINAL IN
center_to_center_distance_between_loop_and_mounting_hole1.796 INCHES MINIMUM AND 1.828 INCHES MAXIMUM IN
NSN5340-00-741-2995
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 3633128 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
STYLE DESIGNATOR: CENTER MOUNT
•
MATERIAL DOCUMENT AND CLASSIFICATION: ASTMA108 ASSN STD SINGLE MATERIAL RESPONSE BAND
•
DIAMETER: 0.422 INCHES MINIMUM AND 0.454 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.111 INCHES MINIMUM AND 0.141 INCHES MAXIMUM IN
•
DISTANCE FROM LOOP CENTER TO TONGUE END: 2.375 INCHES NOMINAL IN
•
TONGUE HOLE TYPE: ROUND, UNTHREADED
•
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 1.796 INCHES MINIMUM AND 1.828 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS
STYLE DESIGNATORCENTER MOUNT
MATERIAL DOCUMENT AND CLASSIFICATIONASTMA108 ASSN STD SINGLE MATERIAL RESPONSE BAND
DIAMETER0.422 INCHES MINIMUM AND 0.454 INCHES MAXIMUM IN
OVERALL WIDTH1.000 INCHES NOMINAL IN
MATERIAL THICKNESS0.111 INCHES MINIMUM AND 0.141 INCHES MAXIMUM IN
DISTANCE FROM LOOP CENTER TO TONGUE END2.375 INCHES NOMINAL IN
TONGUE HOLE TYPEROUND, UNTHREADED
CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE1.796 INCHES MINIMUM AND 1.828 INCHES MAXIMUM IN
MATERIALSTEEL COMP 1010 BAND
DISTANCE FROM LOOP CENTER TO SHORT TONGUE END2.265 INCHES NOMINAL IN
SUBSTITUTES & CROSS-REFERENCES 4
7412995Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
352731Reference document
Same NSN cross-reference
Reference document — Secondary reference
3634389Reference document
Same NSN cross-reference
Reference document — Design control — primary reference
2241299Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusCancelled· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 3633128?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 3633128?
3633128 is a CLAMP,LOOP.
What parts can replace 3633128?
There are 4 known substitutes for 3633128: 7412995, 352731, 3634389 and 1 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 3633128?
3633128 is cataloged in the U.S. Government catalog under NSN 5340-00-741-2995. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 3633128