PartsTable
Technical Data Sheet
Download PDF

35004-64 — BEARING,ROLLER,NEEDLE

✓ Government record, cited
— · TAPERED BEARING
PRODUCT OVERVIEW

35004-64: BEARING,ROLLER,NEEDLE.

The BEARING,ROLLER,NEEDLE is a the manufacturer industrial component. Key specifications include material: STEEL OVERALL, bore_diameter: 1.7500 INCHES NOMINAL IN, overall_width: 1.5100 INCHES NOMINAL IN, alignment_type: RIGID, surface_finish: GROUND, special_features: OIL HOLE AND OIL GROOVE IN OUTER RACE,OIL HOLE AND OIL GROOVE IN INNER RACE,MFR STD RETAINER. This part is cataloged in the U.S.

Government catalog under NSN 3110-00-227-3221, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
35004-64
NSN: 3110-00-227-3221
FSC: 3110 — Bearings, Antifriction, Unmounted
CAGE: 34712 — LAKE SHORE SYSTEMS, INC. (USA)
SPECIFICATIONS
materialSTEEL OVERALL
bore_diameter1.7500 INCHES NOMINAL IN
overall_width1.5100 INCHES NOMINAL IN
alignment_typeRIGID
surface_finishGROUND
special_featuresOIL HOLE AND OIL GROOVE IN OUTER RACE,OIL HOLE AND OIL GROOVE IN INNER RACE,MFR STD RETAINER
style_designatorSEPARABLE INNER RACE, WITH ROLLER RETAINER, HARDENED AND GROUND
overall_outside_diameter2.9994 INCHES MINIMUM AND 3.0000 INCHES MAXIMUM IN
retainer_fabrication_methodPRESSED
standard_tolerance_designationAFBMA STD TOLERANCE FOR INDUSTRIAL NEEDLE BEARINGS
NSN3110-00-227-3221
COMPONENT DIAGRAM
TAPERED ROLLER BEARING — CUP & CONE ASSEMBLY CAGE CUP BORE CONE OD: — · BORE: — · WIDTH: — Single Row · PN: 35004-64 · OEM ⚠ VERIFY BEFORE ORDERING Cup and cone sold separately — verify you are ordering BOTH parts or the correct component. Always replace cup and cone together — mismatched wear = premature failure ✓ BROKER TIP Taper angle determines axial load capacity. Steeper angle = higher axial load rating. Timken series numbers indicate dimensions — cross-reference carefully PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
RETAINER FABRICATION METHOD: PRESSED
•
SURFACE FINISH: GROUND
•
STYLE DESIGNATOR: SEPARABLE INNER RACE, WITH ROLLER RETAINER, HARDENED AND GROUND
•
OVERALL OUTSIDE DIAMETER: 2.9994 INCHES MINIMUM AND 3.0000 INCHES MAXIMUM IN
•
ALIGNMENT TYPE: RIGID
•
STANDARD TOLERANCE DESIGNATION: AFBMA STD TOLERANCE FOR INDUSTRIAL NEEDLE BEARINGS
TECHNICAL CHARACTERISTICS
RETAINER FABRICATION METHODPRESSED
SURFACE FINISHGROUND
STYLE DESIGNATORSEPARABLE INNER RACE, WITH ROLLER RETAINER, HARDENED AND GROUND
OVERALL WIDTH1.5100 INCHES NOMINAL IN
OVERALL OUTSIDE DIAMETER2.9994 INCHES MINIMUM AND 3.0000 INCHES MAXIMUM IN
ALIGNMENT TYPERIGID
SPECIAL FEATURESOIL HOLE AND OIL GROOVE IN OUTER RACE,OIL HOLE AND OIL GROOVE IN INNER RACE,MFR STD RETAINER
STANDARD TOLERANCE DESIGNATIONAFBMA STD TOLERANCE FOR INDUSTRIAL NEEDLE BEARINGS
BORE DIAMETER1.7500 INCHES NOMINAL IN
MATERIALSTEEL OVERALL
SUBSTITUTES & CROSS-REFERENCES 8
MR36NMI28NReference document
Same NSN cross-reference
Reference document — Secondary reference
701-7070554 SH 1 PC 4Reference document
Same NSN cross-reference
Reference document — Advisory reference — outside the item-of-supply concept
MS500072-24Reference document
Same NSN cross-reference
Reference document — Secondary reference
ASTM F 2430Reference document
Same NSN cross-reference
Reference document — Design control — primary reference
MR36NM1-28NReference document
Same NSN cross-reference
Reference document — Secondary reference
HJ364824IR283624Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 35004-64?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 35004-64?
35004-64 is a BEARING,ROLLER,NEEDLE.
What parts can replace 35004-64?
There are 8 known substitutes for 35004-64: MR36NMI28N, 701-7070554 SH 1 PC 4, MS500072-24 and 5 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 35004-64?
35004-64 is cataloged in the U.S. Government catalog under NSN 3110-00-227-3221. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 35004-64