PartsTable
Technical Data Sheet
PartsTable / COMPONENT / 32-58070-37
32-58070-37 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The GASKET is a the manufacturer industrial component. Key specifications include overall_width: 2.812 INCHES NOMINAL IN, overall_length: 2.812 INCHES NOMINAL IN, aperture_diameter: 1.810 INCHES MINIMUM AND 1.870 INCHES MAXIMUM IN, surface_treatment: ANODIZE OVERALL, gage_ring_thickness: 0.076 INCHES MINIMUM AND 0.084 INCHES MAXIMUM IN, fsc_application_data: FUEL LINES,FABRICATED,AIRFRAME. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-819-4572, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
32-58070-37
NSN: 5330-00-819-4572
FSC: 5330
CAGE: 76301 — THE BOEING COMPANY DIV DEFENSE (USA)
SPECIFICATIONS
overall_width2.812 INCHES NOMINAL IN
overall_length2.812 INCHES NOMINAL IN
aperture_diameter1.810 INCHES MINIMUM AND 1.870 INCHES MAXIMUM IN
surface_treatmentANODIZE OVERALL
gage_ring_thickness0.076 INCHES MINIMUM AND 0.084 INCHES MAXIMUM IN
fsc_application_dataFUEL LINES,FABRICATED,AIRFRAME
outside_corner_radius0.500 INCHES NOMINAL IN
end_item_identificationW/S: CONSOLIDATED TARGETS; F4S AIRCRAFT, AIRCRAFT, PHANTOM F-4; F4N AIRCRAFT
cross-sectional_thickness0.116 INCHES MINIMUM AND 0.124 INCHES MAXIMUM IN
cross-sectional_shape_styleMETAL AND SYNTHETIC RUBBER
surface_treatment_document_and_classificationMIL-A-8625,TY 2 MIL SPEC SINGLE TREATMENT RESPONSE OVERALL
outside_edge_to_bolt_hole_center_distance_along_width0.500 INCHES NOMINAL IN
NSN5330-00-819-4572
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 32-58070-37 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG WIDTH: 0.500 INCHES NOMINAL IN
•
CROSS-SECTIONAL THICKNESS: 0.116 INCHES MINIMUM AND 0.124 INCHES MAXIMUM IN
•
GAGE RING THICKNESS: 0.076 INCHES MINIMUM AND 0.084 INCHES MAXIMUM IN
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: MIL-A-8625,TY 2 MIL SPEC SINGLE TREATMENT RESPONSE OVERALL
•
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH: 1.812 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
•
SURFACE TREATMENT: ANODIZE OVERALL
•
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG WIDTH: 1.812 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
TECHNICAL CHARACTERISTICS (FLIS)
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG WIDTH0.500 INCHES NOMINAL IN
CROSS-SECTIONAL THICKNESS0.116 INCHES MINIMUM AND 0.124 INCHES MAXIMUM IN
OVERALL LENGTH2.812 INCHES NOMINAL IN
GAGE RING THICKNESS0.076 INCHES MINIMUM AND 0.084 INCHES MAXIMUM IN
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONMIL-A-8625,TY 2 MIL SPEC SINGLE TREATMENT RESPONSE OVERALL
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH1.812 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
SURFACE TREATMENTANODIZE OVERALL
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG WIDTH1.812 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH0.500 INCHES NOMINAL IN
FSC APPLICATION DATAFUEL LINES,FABRICATED,AIRFRAME
VERIFIED SUBSTITUTES & CROSS-REFERENCES 9
7512X1Interchangeable
interchangeable cross-reference
interchangeable
212KDInterchangeable
interchangeable cross-reference
interchangeable
81516Interchangeable
interchangeable cross-reference
interchangeable
F-F-300Interchangeable
interchangeable cross-reference
interchangeable
ASTM F872Interchangeable
interchangeable cross-reference
interchangeable
124656Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy 32-58070-37?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 32-58070-37?
32-58070-37 is a GASKET.
What parts can replace 32-58070-37?
There are 9 known substitutes for 32-58070-37: 7512X1, 212KD, 81516 and 6 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 32-58070-37?
32-58070-37 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-819-4572. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 32-58070-37

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026