PartsTable
Technical Data Sheet
Download PDF

30-302-2D08J25 — CLAMP,LOOP

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

30-302-2D08J25: CLAMP,LOOP.

The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.199 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN, material: ALUMINUM ALLOY 2024 BAND, loop_width: 0.485 INCHES MINIMUM AND 0.515 INCHES MAXIMUM IN, loop_length: 1.5475 INCHES MINIMUM AND 1.5775 INCHES MAXIMUM IN, overall_width: 0.620 INCHES MINIMUM AND 0.630 INCHES MAXIMUM IN, style_designator: RECTANGULAR. This part is cataloged in the U.S.

Government catalog under NSN 5340-01-711-2128, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
30-302-2D08J25
NSN: 5340-01-711-2128
FSC: 5340 — Hardware, Commercial
CAGE: 97499 — BELL TEXTRON INC (USA)
SPECIFICATIONS
diameter0.199 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN
materialALUMINUM ALLOY 2024 BAND
loop_width0.485 INCHES MINIMUM AND 0.515 INCHES MAXIMUM IN
loop_length1.5475 INCHES MINIMUM AND 1.5775 INCHES MAXIMUM IN
overall_width0.620 INCHES MINIMUM AND 0.630 INCHES MAXIMUM IN
style_designatorRECTANGULAR
tongue_hole_typeROUND, UNTHREADED
surface_treatmentCHROMATE BAND
material_thickness0.040 INCHES NOMINAL IN
specification/standard_data97499-30-302 MANUFACTURERS STANDARD
material_document_and_classificationMIL-DTL-25988,CLASS 2,TYPE II,GRADE 50,COLOR BLUE MIL SPEC SINGLE MATERIAL RESPONSE CUSHION
distance_from_loop_center_to_tongue_end1.44125 INCHES NOMINAL IN
NSN5340-01-711-2128
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 30-302-2D08J25 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: MIL-DTL-5541,CLASS 1A MIL SPEC SINGLE TREATMENT RESPONSE BAND A
•
LOOP WIDTH: 0.485 INCHES MINIMUM AND 0.515 INCHES MAXIMUM IN
•
STYLE DESIGNATOR: RECTANGULAR
•
MATERIAL DOCUMENT AND CLASSIFICATION: AMS-QQ-A-250/5,TREADED TO T42 CONDITION PER AMS-H-6088, NATIONAL STD/SPEC SINGLE MATERIAL RESPONSE BAND
•
DIAMETER: 0.199 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN
•
MATERIAL THICKNESS: 0.040 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONMIL-DTL-5541,CLASS 1A MIL SPEC SINGLE TREATMENT RESPONSE BAND A
LOOP WIDTH0.485 INCHES MINIMUM AND 0.515 INCHES MAXIMUM IN
STYLE DESIGNATORRECTANGULAR
MATERIAL DOCUMENT AND CLASSIFICATIONAMS-QQ-A-250/5,TREADED TO T42 CONDITION PER AMS-H-6088, NATIONAL STD/SPEC SINGLE MATERIAL RESPONSE BAND
MATERIAL DOCUMENT AND CLASSIFICATIONMIL-DTL-25988,CLASS 2,TYPE II,GRADE 50,COLOR BLUE MIL SPEC SINGLE MATERIAL RESPONSE CUSHION
DIAMETER0.199 INCHES MINIMUM AND 0.209 INCHES MAXIMUM IN
OVERALL WIDTH0.620 INCHES MINIMUM AND 0.630 INCHES MAXIMUM IN
MATERIAL THICKNESS0.040 INCHES NOMINAL IN
DISTANCE FROM LOOP CENTER TO TONGUE END1.44125 INCHES NOMINAL IN
SPECIFICATION/STANDARD DATA97499-30-302 MANUFACTURERS STANDARD
SUBSTITUTES & CROSS-REFERENCES 1
30-302Reference document
Same NSN cross-reference
Reference document — Drawing number reference only
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 30-302-2D08J25?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 30-302-2D08J25?
30-302-2D08J25 is a CLAMP,LOOP.
What parts can replace 30-302-2D08J25?
There is 1 known substitute for 30-302-2D08J25: 30-302. Substitute compatibility should be verified for your specific system.
What is the NSN for 30-302-2D08J25?
30-302-2D08J25 is cataloged in the U.S. Government catalog under NSN 5340-01-711-2128. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 30-302-2D08J25

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.