2LN — CLAMP,LOOP
✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW
2LN: CLAMP,LOOP.
The CLAMP,LOOP is a the manufacturer industrial component. Key specifications include diameter: 0.203 INCHES NOMINAL IN, material: PLASTIC POLYAMIDE NYLON OVERALL, overall_width: 0.380 INCHES NOMINAL IN, style_designator: SINGLE LOOP, tongue_hole_type: ROUND, UNTHREADED, material_thickness: 0.050 INCHES NOMINAL IN. This part is cataloged in the U.S.
Government catalog under NSN 5340-01-109-3349, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.
Verify compatibility with your specific system configuration before ordering.
WHERE IT FITS
2LN
NSN: 5340-01-109-3349 FSC: 5340 — Hardware, CommercialCAGE: 26863 — ALL-STATES INC. (USA)
SPECIFICATIONS
diameter 0.203 INCHES NOMINAL IN material PLASTIC POLYAMIDE NYLON OVERALL overall_width 0.380 INCHES NOMINAL IN style_designator SINGLE LOOP tongue_hole_type ROUND, UNTHREADED material_thickness 0.050 INCHES NOMINAL IN loop_inside_diameter 0.115 INCHES MINIMUM AND 0.125 INCHES MAXIMUM IN distance_from_loop_center_to_tongue_end 0.550 INCHES NOMINAL IN center_to_center_distance_between_loop_and_mounting_hole 0.330 INCHES NOMINAL IN NSN 5340-01-109-3349
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION
ID: —
CROSS-SECTION
CS: —
SPECIFICATION
Material: —
Durometer: —
Temp: —
PN: 2LN
MFR: OEM
⚠ VERIFY BEFORE ORDERING
Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade.
Chemical incompatibility causes swelling, brittleness, or rapid degradation
✓ BROKER TIP
Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure.
Standard durometer is 70A — verify if application requires different hardness
PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
• STYLE DESIGNATOR: SINGLE LOOP
• DIAMETER: 0.203 INCHES NOMINAL IN
• MATERIAL THICKNESS: 0.050 INCHES NOMINAL IN
• DISTANCE FROM LOOP CENTER TO TONGUE END: 0.550 INCHES NOMINAL IN
• TONGUE HOLE TYPE: ROUND, UNTHREADED
• CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE: 0.330 INCHES NOMINAL IN
• MATERIAL: PLASTIC POLYAMIDE NYLON OVERALL
TECHNICAL CHARACTERISTICS
STYLE DESIGNATOR SINGLE LOOP DIAMETER 0.203 INCHES NOMINAL IN OVERALL WIDTH 0.380 INCHES NOMINAL IN MATERIAL THICKNESS 0.050 INCHES NOMINAL IN DISTANCE FROM LOOP CENTER TO TONGUE END 0.550 INCHES NOMINAL IN TONGUE HOLE TYPE ROUND, UNTHREADED CENTER TO CENTER DISTANCE BETWEEN LOOP AND MOUNTING HOLE 0.330 INCHES NOMINAL IN MATERIAL PLASTIC POLYAMIDE NYLON OVERALL LOOP INSIDE DIAMETER 0.115 INCHES MINIMUM AND 0.125 INCHES MAXIMUM IN
SUBSTITUTES & CROSS-REFERENCES 2
150-1554-000 Reference document Same NSN cross-reference
Reference document — Vendor item drawing reference
1/8LN Reference document Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN status Active · U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM) No demilitarization required
Ready to buy 2LN?
Compare prices from verified sellers on eBay
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 2LN?
2LN is a CLAMP,LOOP.
What parts can replace 2LN?
There are 2 known substitutes for 2LN: 150-1554-000, 1/8LN. Substitute compatibility should be verified for your specific system.
What is the NSN for 2LN?
2LN is cataloged in the U.S. Government catalog under NSN 5340-01-109-3349. This indicates validated use in U.S. government and defense supply chains.