PartsTable
Technical Data Sheet
Download PDF

21D334 — BEARING,BALL,ANNULAR

✓ Government record, cited
— · TAPERED BEARING
PRODUCT OVERVIEW

21D334: BEARING,BALL,ANNULAR.

The BEARING,BALL,ANNULAR is a the manufacturer industrial component. Key specifications include material: COPPER ALLOY RETAINER, bore_shape: STRAIGHT, bore_diameter: 3.9344 INCHES MINIMUM AND 3.9353 INCHES MAXIMUM IN, load_direction: RADIAL, surface_finish: GROUND, inner_ring_width: 1.3800 INCHES MINIMUM AND 1.3850 INCHES MAXIMUM IN. This part is cataloged in the U.S.

Government catalog under NSN 3110-00-447-4855, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
21D334
NSN: 3110-00-447-4855
FSC: 3110 — Bearings, Antifriction, Unmounted
CAGE: 0AHP5 — CURTISS-WRIGHT CONTROLS, INC. DIV ACTUATION DIVISION (USA)
SPECIFICATIONS
materialCOPPER ALLOY RETAINER
bore_shapeSTRAIGHT
bore_diameter3.9344 INCHES MINIMUM AND 3.9353 INCHES MAXIMUM IN
load_directionRADIAL
surface_finishGROUND
inner_ring_width1.3800 INCHES MINIMUM AND 1.3850 INCHES MAXIMUM IN
outer_ring_width1.3850 INCHES NOMINAL IN
special_featuresSPLIT INNER RING
internal_clearance0.0013 INCHES MINIMUM RADIAL AND 0.0032 INCHES MAXIMUM RADIAL IN
overall_outside_diameter7.0876 INCHES MINIMUM AND 7.0886 INCHES MAXIMUM IN
retainer_fabrication_methodMACHINED
NSN3110-00-447-4855
COMPONENT DIAGRAM
TAPERED ROLLER BEARING — CUP & CONE ASSEMBLY CAGE CUP BORE CONE OD: — · BORE: — · WIDTH: — Single Row · PN: 21D334 · OEM ⚠ VERIFY BEFORE ORDERING Cup and cone sold separately — verify you are ordering BOTH parts or the correct component. Always replace cup and cone together — mismatched wear = premature failure ✓ BROKER TIP Taper angle determines axial load capacity. Steeper angle = higher axial load rating. Timken series numbers indicate dimensions — cross-reference carefully PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
RETAINER FABRICATION METHOD: MACHINED
•
OUTER RING WIDTH: 1.3850 INCHES NOMINAL IN
•
INTERNAL CLEARANCE: 0.0013 INCHES MINIMUM RADIAL AND 0.0032 INCHES MAXIMUM RADIAL IN
•
SURFACE FINISH: GROUND
•
OVERALL OUTSIDE DIAMETER: 7.0876 INCHES MINIMUM AND 7.0886 INCHES MAXIMUM IN
•
BORE SHAPE: STRAIGHT
•
LOAD DIRECTION: RADIAL
TECHNICAL CHARACTERISTICS
RETAINER FABRICATION METHODMACHINED
OUTER RING WIDTH1.3850 INCHES NOMINAL IN
INTERNAL CLEARANCE0.0013 INCHES MINIMUM RADIAL AND 0.0032 INCHES MAXIMUM RADIAL IN
SURFACE FINISHGROUND
OVERALL OUTSIDE DIAMETER7.0876 INCHES MINIMUM AND 7.0886 INCHES MAXIMUM IN
BORE SHAPESTRAIGHT
LOAD DIRECTIONRADIAL
SPECIAL FEATURESSPLIT INNER RING
BORE DIAMETER3.9344 INCHES MINIMUM AND 3.9353 INCHES MAXIMUM IN
MATERIALCOPPER ALLOY RETAINER
SUBSTITUTES & CROSS-REFERENCES 3
D2-39473Reference document
Same NSN cross-reference
Reference document — Secondary reference
9220U23Reference document
Same NSN cross-reference
Reference document — Secondary reference
461673Reference document
Same NSN cross-reference
Reference document — Secondary reference
LIFECYCLE
NSN statusCancelled· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 21D334?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 21D334?
21D334 is a BEARING,BALL,ANNULAR.
What parts can replace 21D334?
There are 3 known substitutes for 21D334: D2-39473, 9220U23, 461673. Substitute compatibility should be verified for your specific system.
What is the NSN for 21D334?
21D334 is cataloged in the U.S. Government catalog under NSN 3110-00-447-4855. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 21D334