205-040-245: BEARING,BALL,DUPLEX.
The BEARING,BALL,DUPLEX is a the manufacturer industrial component. Key specifications include material: STEEL OVERALL, bore_diameter: 4.7232 INCHES MINIMUM AND 4.7235 INCHES MAXIMUM IN, overall_width: 1.7023 INCHES MINIMUM AND 1.7323 INCHES MAXIMUM IN, load_direction: ANGULAR, surface_finish: GROUND, special_features: INCLUDE A STEEL RETAINER. This part is cataloged in the U.S.
Government catalog under NSN 3110-00-133-3379, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.
Verify compatibility with your specific system configuration before ordering.
| material | STEEL OVERALL |
| bore_diameter | 4.7232 INCHES MINIMUM AND 4.7235 INCHES MAXIMUM IN |
| overall_width | 1.7023 INCHES MINIMUM AND 1.7323 INCHES MAXIMUM IN |
| load_direction | ANGULAR |
| surface_finish | GROUND |
| special_features | INCLUDE A STEEL RETAINER |
| style_designator | COUNTERBORED OUTER RINGS, NON-SEPARABLE, BACK TO BACK MOUNTING |
| bearing_preload_rating | 22.0 POUNDS NOMINAL LBS |
| end_item_identification | UH-1N |
| overall_outside_diameter | 6.6924 INCHES MINIMUM AND 6.6929 INCHES MAXIMUM IN |
| internal_fit-up_designation | STANDARD |
| retainer_fabrication_method | MACHINED |
| NSN | 3110-00-133-3379 |
| BEARING PRELOAD RATING | 22.0 POUNDS NOMINAL LBS |
| INTERNAL FIT-UP DESIGNATION | STANDARD |
| SURFACE FINISH | GROUND |
| STYLE DESIGNATOR | COUNTERBORED OUTER RINGS, NON-SEPARABLE, BACK TO BACK MOUNTING |
| MATERIAL DOCUMENT AND CLASSIFICATION | UNABLE TO DECODE |
| OVERALL WIDTH | 44.00 MILLIMETERS NOMINAL MM |
| OVERALL OUTSIDE DIAMETER | 170.00 MILLIMETERS NOMINAL MM |
| LOAD DIRECTION | ANGULAR |
| SPECIAL FEATURES | BEARINGS MARKED WITH SAME SER NO.,BEARINGS STABILIZED FOR OPERATION FROM M65 DEG F TO P500 DEG F |
| TEST DATA DOCUMENT | 21335-APS33 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). AND 21335-APS36-A SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). AND 38443-AQC+2-A SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). AND 38443-AQC+9-A SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |