204-040-424: BEARING,BALL,DUPLEX.
The BEARING,BALL,DUPLEX is a the manufacturer industrial component. Key specifications include material: STEEL OVERALL, bore_diameter: 1.5745 INCHES MINIMUM AND 1.5748 INCHES MAXIMUM IN, overall_width: 0.9249 INCHES MINIMUM AND 0.9449 INCHES MAXIMUM IN, load_direction: ANGULAR, surface_finish: GROUND, special_features: STEEL CAGE BEARING. This part is cataloged in the U.S.
Government catalog under NSN 3110-00-088-3399, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.
Verify compatibility with your specific system configuration before ordering.
| material | STEEL OVERALL |
| bore_diameter | 1.5745 INCHES MINIMUM AND 1.5748 INCHES MAXIMUM IN |
| overall_width | 0.9249 INCHES MINIMUM AND 0.9449 INCHES MAXIMUM IN |
| load_direction | ANGULAR |
| surface_finish | GROUND |
| special_features | STEEL CAGE BEARING |
| style_designator | COUNTERBORED OUTER RINGS, NON-SEPARABLE, BACK TO BACK MOUNTING |
| end_item_identification | UH-1N |
| overall_outside_diameter | 2.6770 INCHES MINIMUM AND 2.6773 INCHES MAXIMUM IN |
| internal_fit-up_designation | STANDARD |
| retainer_fabrication_method | MACHINED |
| standard_tolerance_designation | ABEC NO.3 |
| NSN | 3110-00-088-3399 |
| INTERNAL FIT-UP DESIGNATION | STANDARD |
| SURFACE FINISH | GROUND |
| STYLE DESIGNATOR | COUNTERBORED OUTER RINGS, NON-SEPARABLE, BACK TO BACK MOUNTING |
| MATERIAL DOCUMENT AND CLASSIFICATION | UNABLE TO DECODE |
| OVERALL WIDTH | 0.9448 INCHES NOMINAL IN |
| OVERALL OUTSIDE DIAMETER | 2.6774 INCHES NOMINAL IN |
| LOAD DIRECTION | ANGULAR |
| SPECIAL FEATURES | BEARINGS MARKED W/SAME SERIAL NO.,BEARINGS STABILIZED FOR OPERATION AT M 65 TO P 300 DEG F DEGF |
| TEST DATA DOCUMENT | 21335-PS33 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). AND 21335-P S36 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). AND 38443-QCP-9 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). AND 52676-470377 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| STANDARD TOLERANCE DESIGNATION | ABEC NO.3 |