PartsTable
Technical Data Sheet
PartsTable / MRO / 2013-20
2013-20 ✓ Verified by PartsTable
— · MRO · MRO_GENERAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The RESISTOR,FIXED,COMPOSITION is a the manufacturer industrial component. Key specifications include phase: THREE, material: STEEL ALLOY OVERALL, frame_type: RIGID, point_type: SPLIT, table_type: TILTING, body_length: 0.344 INCHES MINIMUM AND 0.406 INCHES MAXIMUM IN. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-291-7435, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MRO→ MRO_GENERAL→ 2013-20
NSN: 5330-00-291-7435
FSC: 5330
CAGE: U2621 — MARINE & INDUSTRIAL TRANSMISSIONS LTD (GBR)
SPECIFICATIONS
phaseTHREE
materialSTEEL ALLOY OVERALL
frame_typeRIGID
point_typeSPLIT
table_typeTILTING
body_length0.344 INCHES MINIMUM AND 0.406 INCHES MAXIMUM IN
point_angle135.0 DEGREES NOMINAL
shank_styleSTRAIGHT ROUND
table_width32.000 INCHES NOMINAL IN
current_typeAC
drive_methodELECTRIC MOTOR
flute_length2.125 INCHES NOMINAL IN
NSN5330-00-291-7435
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 2013-20 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH: 2.000 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
•
APERTURE DIAMETER: 1.875 INCHES NOMINAL IN
•
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH: 0.500 INCHES NOMINAL IN
•
MATERIAL: RUBBER CHLOROPRENE CLASS CR OVERALL
•
CROSS-SECTIONAL THICKNESS: 0.031 INCHES NOMINAL IN
•
BOLT HOLE QUANTITY: 4
TECHNICAL CHARACTERISTICS (FLIS)
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG LENGTH2.000 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
APERTURE DIAMETER1.875 INCHES NOMINAL IN
OUTSIDE EDGE TO BOLT HOLE CENTER DISTANCE ALONG LENGTH0.500 INCHES NOMINAL IN
MATERIALRUBBER CHLOROPRENE CLASS CR OVERALL
CROSS-SECTIONAL THICKNESS0.031 INCHES NOMINAL IN
OVERALL WIDTH3.000 INCHES NOMINAL IN
BOLT HOLE QUANTITY4
OVERALL LENGTH3.000 INCHES NOMINAL IN
HOLE DIAMETER0.375 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
CENTER TO CENTER DISTANCE BETWEEN BOLT HOLES ALONG WIDTH2.000 INCHES NOMINAL LOCATION NOT OTHERWISE SPECIFIED IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 12
60-23-9652Interchangeable
interchangeable cross-reference
interchangeable
245205Interchangeable
interchangeable cross-reference
interchangeable
787-24-02-004Interchangeable
interchangeable cross-reference
interchangeable
46690Interchangeable
interchangeable cross-reference
interchangeable
550 20Interchangeable
interchangeable cross-reference
interchangeable
818 20Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy 2013-20?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 2013-20?
2013-20 is a RESISTOR,FIXED,COMPOSITION. It is classified as a MRO (MRO_GENERAL).
What parts can replace 2013-20?
There are 12 known substitutes for 2013-20: 60-23-9652, 245205, 787-24-02-004 and 9 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 2013-20?
2013-20 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-291-7435. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 2013-20

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026