PartsTable
Technical Data Sheet
Download PDF

165612 — RESISTOR,VARIABLE,NONWIRE WOUND,

✓ Government record, cited
— · MRO · MRO_GENERAL
PRODUCT OVERVIEW

165612: RESISTOR,VARIABLE,NONWIRE WOUND,.

RESISTOR,VARIABLE,NONWIRE WOUND,. Key specifications include angle: 25.0 DEGREES MINIMUM AND 35.0 DEGREES MAXIMUM, material: PLASTIC TETRAFLUOROETHYLENE OVERALL, joint_type: SCARF-BUTT RETAINER, shaft_style: ROUND, SLOTTED, shaft_length: 0.875 INCHES NOMINAL IN, actuator_type: SINGLE SHAFT. This part is cataloged in the U.S.

Government catalog under NSN 5330-00-171-5100, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
MRO→ MRO_GENERAL→ 165612
NSN: 5330-00-171-5100
NIINs: 001715100, 005438950, 014392512
FSC: 5330 — Packing and Gasket Materials
CAGE: 29510 — KOMATSU AMERICAN INTL CO (USA)
SPECIFICATIONS
angle25.0 DEGREES MINIMUM AND 35.0 DEGREES MAXIMUM
materialPLASTIC TETRAFLUOROETHYLENE OVERALL
joint_typeSCARF-BUTT RETAINER
shaft_styleROUND, SLOTTED
shaft_length0.875 INCHES NOMINAL IN
actuator_typeSINGLE SHAFT
shaft_diameter0.250 INCHES NOMINAL IN
section_quantity1
peripheral_diameter2.238 INCHES MINIMUM AND 2.242 INCHES MAXIMUM IN
center_hole_diameter2.000 INCHES NOMINAL IN
distance_between_ends0.093 INCHES MINIMUM AND 0.250 INCHES MAXIMUM IN
reliability_indicatorNOT ESTABLISHED
NSN5330-00-171-5100
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 165612 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CROSS-SECTIONAL THICKNESS: 0.025 INCHES MINIMUM AND 0.029 INCHES MAXIMUM IN
•
CROSS-SECTIONAL HEIGHT: 0.075 INCHES MINIMUM AND 0.087 INCHES MAXIMUM IN
•
MATERIAL DOCUMENT AND CLASSIFICATION: SAE-AS8791 NATIONAL SPEC SINGLE MATERIAL RESPONSE OVERALL
•
CROSS-SECTIONAL SHAPE STYLE: SQUARE
•
ANGLE: 25.0 DEGREES MINIMUM AND 35.0 DEGREES MAXIMUM
•
PERIPHERAL DIAMETER: 2.238 INCHES MINIMUM AND 2.242 INCHES MAXIMUM IN
•
DISTANCE BETWEEN ENDS: 0.093 INCHES MINIMUM AND 0.250 INCHES MAXIMUM IN
•
CENTER HOLE DIAMETER: 2.000 INCHES NOMINAL IN
TECHNICAL CHARACTERISTICS
CROSS-SECTIONAL THICKNESS0.025 INCHES MINIMUM AND 0.029 INCHES MAXIMUM IN
CROSS-SECTIONAL HEIGHT0.075 INCHES MINIMUM AND 0.087 INCHES MAXIMUM IN
MATERIAL DOCUMENT AND CLASSIFICATIONSAE-AS8791 NATIONAL SPEC SINGLE MATERIAL RESPONSE OVERALL
CROSS-SECTIONAL SHAPE STYLESQUARE
ANGLE25.0 DEGREES MINIMUM AND 35.0 DEGREES MAXIMUM
PERIPHERAL DIAMETER2.238 INCHES MINIMUM AND 2.242 INCHES MAXIMUM IN
DISTANCE BETWEEN ENDS0.093 INCHES MINIMUM AND 0.250 INCHES MAXIMUM IN
CENTER HOLE DIAMETER2.000 INCHES NOMINAL IN
MATERIALPLASTIC TETRAFLUOROETHYLENE OVERALL
JOINT TYPESCARF-BUTT RETAINER
SUBSTITUTES & CROSS-REFERENCES 9
54-94-8304Reference document
Same NSN cross-reference
Reference document — Secondary reference
2034997Reference document
Same NSN cross-reference
Reference document — Secondary reference
MS28783-4Reference document
Same NSN cross-reference
Reference document — Advisory reference — outside the item-of-supply concept
MS35803-226Reference document
Same NSN cross-reference
Reference document — Secondary reference
80111-4Reference document
Same NSN cross-reference
Reference document — Secondary reference
5330PL1028837Reference document
Same NSN cross-reference
Reference document — Informative reference only
LIFECYCLE
NSN statusCancelled· U.S. Government catalog
Acquisition advice: Insurance item — stocked against contingency demandNo demilitarization required
Ready to buy 165612?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 165612?
165612 is a RESISTOR,VARIABLE,NONWIRE WOUND,. It is classified as a MRO (MRO_GENERAL).
What parts can replace 165612?
There are 9 known substitutes for 165612: 54-94-8304, 2034997, MS28783-4 and 6 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 165612?
165612 is cataloged in the U.S. Government catalog under NSN 5330-00-171-5100. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 165612

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.