PartsTable
Technical Data Sheet
16-408 ✓ Verified by PartsTable
Clementoni · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

<b>Key features:</b><br>- Up to 80 GB capacity with hardware data compression on a single cartridge.<br>- Up to 6 MB/sec. data transfer rate.<br>- 80 GB backup in less than 4 hours.<br>- Compact 5,25 inch half height form factor.<br>- Read compatible with DLT1 and DLT4000.<br>- Uses standard DLTtape IV media.<br>- Internal and external solution.<br>- TapeAlertTM monitors drive and cartridge to warn in case of problems.<br>- 200.000 hrs MTBF at a 100% duty cycle.<br>- Support of nearly all operating Systems and platforms. This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-078-2533, indicating validated use in U.S.

government and defense logistics supply chains.

WHERE IT FITS
16-408
NSN: 5330-00-078-2533
FSC: 5330
CAGE: 28953 — RIX INDUSTRIES (USA)
SPECIFICATIONS
materialSTEEL BODY
thickness0.022 INCHES MINIMUM AND 0.042 INCHES MAXIMUM IN
head_styleFILLISTER
scale_typeECCENTRIC
body_length4.250 INCHES MAXIMUM IN
head_height0.055 INCHES MINIMUM AND 0.062 INCHES MAXIMUM IN
constructionONE-PIECE
scale_length2.625 INCHES NOMINAL IN
thread_class2A A
head_diameter0.124 INCHES MINIMUM AND 0.140 INCHES MAXIMUM IN
hole_diameter0.164 INCHES MINIMUM AND 0.184 INCHES MAXIMUM IN
thread_length0.714 INCHES MINIMUM AND 0.750 INCHES MAXIMUM IN
NSN5330-00-078-2533
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 16-408 MFR: Clementoni ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
SUPPLEMENTARY FEATURES: CROSS-SECTIONAL SHAPE STYLE:NO.195 IRREGULAR SHAPE FROM FIIG A03200
TECHNICAL CHARACTERISTICS (FLIS)
SPECIAL FEATURESSTYLE DESIGNATOR:NO.60 IRREGULAR SHAPE FROM FIIG A03200
SUPPLEMENTARY FEATURESCROSS-SECTIONAL SHAPE STYLE:NO.195 IRREGULAR SHAPE FROM FIIG A03200
VERIFIED SUBSTITUTES & CROSS-REFERENCES 16
150300-0250Interchangeable
interchangeable cross-reference
interchangeable
150300-0205Interchangeable
interchangeable cross-reference
interchangeable
16408Interchangeable
interchangeable cross-reference
interchangeable
K238Interchangeable
interchangeable cross-reference
interchangeable
K-295Interchangeable
interchangeable cross-reference
interchangeable
1269786Interchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy 16-408?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 16-408?
16-408 is a CONNECTOR,PLUG,ELECTRICAL manufactured by Clementoni.
What parts can replace 16-408?
There are 16 known substitutes for 16-408: 150300-0250, 150300-0205, 16408 and 13 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 16-408?
16-408 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5330-00-078-2533. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 16-408