PartsTable
Technical Data Sheet
Download PDF

10911201 REV D — PIN,STRAIGHT,HEADED

✓ Government record, cited
— · NUT WASHER
PRODUCT OVERVIEW

10911201 REV D: PIN,STRAIGHT,HEADED.

The PIN,STRAIGHT,HEADED is a the manufacturer industrial component. Key specifications include height: 1.380 INCHES NOMINAL IN, diameter: 0.370 INCHES MINIMUM AND 0.390 INCHES MAXIMUM IN, material: STEEL COMP 1025 OVERALL, head_style: THUMB NO. 4, head_width: 0.970 INCHES MINIMUM AND 1.030 INCHES MAXIMUM IN, chamfer_length: 0.090 INCHES NOMINAL IN.

This part is cataloged in the U.S. Government catalog under NSN 5315-00-168-2808, indicating validated use in U.S. government and defense logistics supply chains.

Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels. Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
10911201 REV D
NSN: 5315-00-168-2808
FSC: 5315 — Nails, Machine Keys, and Pins
CAGE: 19207 — U S ARMY TANK AUTOMOTIVE COMMAND AMSTA-IM-MM (USA)
SPECIFICATIONS
height1.380 INCHES NOMINAL IN
diameter0.370 INCHES MINIMUM AND 0.390 INCHES MAXIMUM IN
materialSTEEL COMP 1025 OVERALL
head_styleTHUMB NO. 4
head_width0.970 INCHES MINIMUM AND 1.030 INCHES MAXIMUM IN
chamfer_length0.090 INCHES NOMINAL IN
special_features0.515 IN. DIA HOLE DRILLED THRU HEAD IN
style_designatorSTRAIGHT
pin_chamfer_angle45.0 DEGREES NOMINAL
under_head_length6.370 INCHES NOMINAL IN
first_hole_diameter0.515 INCHES MINIMUM AND 0.520 INCHES MAXIMUM IN
hole_arrangement_styleDRILLED THRU HEAD
NSN5315-00-168-2808
COMPONENT DIAGRAM
NUT & WASHER — GRADE MATCHING REQUIRED Hex NUT CROSS-SECTION WASHER OD: — SIZE: — MATERIAL: — PN: 10911201 REV D · OEM ⚠ VERIFY BEFORE ORDERING Grade matters for torque spec — don't mix grades. A Grade 5 nut on a Grade 8 bolt weakens the joint. Lock nuts, wing nuts, and castle nuts are NOT interchangeable with standard hex ✓ BROKER TIP Match nut to bolt thread class and material. Stainless bolt + zinc nut = galvanic corrosion. Always verify finish matches (plain, zinc, hot-dip galvanized) PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CHAMFER LENGTH: 0.090 INCHES NOMINAL IN
•
HOLE ARRANGEMENT STYLE: DRILLED THRU HEAD
•
HEAD WIDTH: 0.970 INCHES MINIMUM AND 1.030 INCHES MAXIMUM IN
•
UNDER HEAD LENGTH: 6.370 INCHES NOMINAL IN
•
PIN CHAMFER ANGLE: 45.0 DEGREES NOMINAL
•
FIRST HOLE DIAMETER: 0.515 INCHES MINIMUM AND 0.520 INCHES MAXIMUM IN
•
STYLE DESIGNATOR: STRAIGHT
•
DIAMETER: 0.370 INCHES MINIMUM AND 0.390 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS
CHAMFER LENGTH0.090 INCHES NOMINAL IN
HOLE ARRANGEMENT STYLEDRILLED THRU HEAD
HEAD WIDTH0.970 INCHES MINIMUM AND 1.030 INCHES MAXIMUM IN
UNDER HEAD LENGTH6.370 INCHES NOMINAL IN
PIN CHAMFER ANGLE45.0 DEGREES NOMINAL
FIRST HOLE DIAMETER0.515 INCHES MINIMUM AND 0.520 INCHES MAXIMUM IN
STYLE DESIGNATORSTRAIGHT
DIAMETER0.370 INCHES MINIMUM AND 0.390 INCHES MAXIMUM IN
HEAD STYLETHUMB NO. 4
HEIGHT1.380 INCHES NOMINAL IN
SUBSTITUTES & CROSS-REFERENCES 1
CS-2300-0001 REV BReference document
Same NSN cross-reference
Reference document — Drawing number reference only
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Normally procured from the manufacturer (OEM)No demilitarization required
Ready to buy 10911201 REV D?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 10911201 REV D?
10911201 REV D is a PIN,STRAIGHT,HEADED.
What parts can replace 10911201 REV D?
There is 1 known substitute for 10911201 REV D: CS-2300-0001 REV B. Substitute compatibility should be verified for your specific system.
What is the NSN for 10911201 REV D?
10911201 REV D is cataloged in the U.S. Government catalog under NSN 5315-00-168-2808. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 10911201 REV D