PartsTable
Technical Data Sheet
Download PDF

10117341 — CAP-PLUG,PROTECTIVE,DUST AND MOI

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

10117341: CAP-PLUG,PROTECTIVE,DUST AND MOI.

CAP-PLUG,PROTECTIVE,DUST AND MOI. Key specifications include material: PLASTIC, POLYETHYLENE (PP), special_features: C0L0R RED, length_under_shoulder: 0.570 INCHES MAXIMUM IN, open_end_inside_diameter: 0.950 INCHES MAXIMUM IN, closed_end_overall_diameter: 1.016 INCHES MAXIMUM IN. This part is cataloged in the U.S.

Government catalog under NSN 5340-00-342-5577, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
10117341
NSN: 5340-00-342-5577
FSC: 5340 — Hardware, Commercial
CAGE: A486G — NIMIKKEISTOKESKUS NCB FINLAND (FIN)
SPECIFICATIONS
materialPLASTIC, POLYETHYLENE (PP)
special_featuresC0L0R RED
length_under_shoulder0.570 INCHES MAXIMUM IN
open_end_inside_diameter0.950 INCHES MAXIMUM IN
closed_end_overall_diameter1.016 INCHES MAXIMUM IN
NSN5340-00-342-5577
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 10117341 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
CLOSED END OVERALL DIAMETER: 1.016 INCHES MAXIMUM IN
•
LENGTH UNDER SHOULDER: 0.570 INCHES MAXIMUM IN
•
OPEN END INSIDE DIAMETER: 0.950 INCHES MAXIMUM IN
•
MATERIAL: PLASTIC, POLYETHYLENE (PP)
TECHNICAL CHARACTERISTICS
CLOSED END OVERALL DIAMETER1.016 INCHES MAXIMUM IN
LENGTH UNDER SHOULDER0.570 INCHES MAXIMUM IN
SPECIAL FEATURESC0L0R RED
OPEN END INSIDE DIAMETER0.950 INCHES MAXIMUM IN
END ITEM IDENTIFICATIONW/S: HELICOPTER, MH-53E; HELICOPTER, CARRIER BASED ASW, SH-60F; HELICOPTER, SEARCH AND RESCUE, HH-60H; HELICOPTER, SEAHAWK, H-60; AIRCRAFT, PHANTOM F-4; HELICOPTER, ADVANCE ATTACK, AH-1W; HELICOPTER, USCG SEARCH AND RESCUE, HH-60J; LAV, ANTI-TANK; ENGINE, AIRCRAFT T-700; MISSILE, TOMAHAWK W
MATERIALPLASTIC, POLYETHYLENE (PP)
SUBSTITUTES & CROSS-REFERENCES 4
025-0466-000Reference document
Same NSN cross-reference
Reference document — Secondary reference
8486438Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
99-779-6059Reference document
Same NSN cross-reference
Reference document — Informative reference only
188462-1Reference document
Same NSN cross-reference
Reference document — Advisory reference — outside the item-of-supply concept
LIFECYCLE
NSN statusCancelled· U.S. Government catalog
Acquisition advice: Insurance item — stocked against contingency demandNo demilitarization required
Ready to buy 10117341?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 10117341?
10117341 is a CAP-PLUG,PROTECTIVE,DUST AND MOI.
What parts can replace 10117341?
There are 4 known substitutes for 10117341: 025-0466-000, 8486438, 99-779-6059 and 1 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 10117341?
10117341 is cataloged in the U.S. Government catalog under NSN 5340-00-342-5577. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 10117341