PartsTable
Technical Data Sheet
PartsTable / O-RING / 10117183
10117183 ✓ Verified by PartsTable
— · ORING SEAL
WHAT YOU NEED TO KNOW
Material determines chemical compatibility Standard durometer is 70 Shore A
Wrong material = catastrophic seal failure
PRODUCT OVERVIEW

The O-RING is a the manufacturer industrial component. Key specifications include material: RUBBER ETHYLENE-PROPYLENE CLASS EPM, temp_rating: -65.0 FAHRENHEIT AND 250.0 FAHRENHEIT DEGF, center_hole_diameter: 0.484 INCHES MINIMUM AND 0.494 INCHES MAXIMUM IN, cross-sectional_height: 0.067 INCHES MINIMUM AND 0.073 INCHES MAXIMUM IN, criticality_code_justification: ZZZY. This product is currently in active production with full OEM support.

This part is cataloged in the Federal Logistics Information System (FLIS) under NSN 5331-01-268-1249, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
10117183
NSN: 5331-01-268-1249
FSC: 5331 — O-RING
CAGE: A486G — NIMIKKEISTOKESKUS NCB FINLAND (FIN)
SPECIFICATIONS
materialRUBBER ETHYLENE-PROPYLENE CLASS EPM
temp_rating-65.0 FAHRENHEIT AND 250.0 FAHRENHEIT DEGF
center_hole_diameter0.484 INCHES MINIMUM AND 0.494 INCHES MAXIMUM IN
cross-sectional_height0.067 INCHES MINIMUM AND 0.073 INCHES MAXIMUM IN
criticality_code_justificationZZZY
reference_number_differentiating_characteristicsAS DIFFERENTIATED BY MATERIAL WHICH MUST CONFORM TO SHIPS PARTS CONTROL CENTER SPECIAL QUALITY CONTROL PROVISIONS AND CERTIFIED FREE FROM MERCURY CONTAMINATION
NSN5331-01-268-1249
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 10117183 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
MATERIAL: RUBBER ETHYLENE-PROPYLENE CLASS EPM
•
CRITICALITY CODE JUSTIFICATION: ZZZY
•
TEMP RATING: -65.0 FAHRENHEIT AND 250.0 FAHRENHEIT DEGF
•
REFERENCE NUMBER DIFFERENTIATING CHARACTERISTICS: AS DIFFERENTIATED BY MATERIAL WHICH MUST CONFORM TO SHIPS PARTS CONTROL CENTER SPECIAL QUALITY CONTROL PROVISIONS AND CERTIFIED FREE FROM MERCURY CONTAMINATION
•
CENTER HOLE DIAMETER: 0.484 INCHES MINIMUM AND 0.494 INCHES MAXIMUM IN
•
TEST DATA DOCUMENT: 81349-MIL-P-23199 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
•
CROSS-SECTIONAL HEIGHT: 0.067 INCHES MINIMUM AND 0.073 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS (FLIS)
MATERIALRUBBER ETHYLENE-PROPYLENE CLASS EPM
CRITICALITY CODE JUSTIFICATIONZZZY
TEMP RATING-65.0 FAHRENHEIT AND 250.0 FAHRENHEIT DEGF
REFERENCE NUMBER DIFFERENTIATING CHARACTERISTICSAS DIFFERENTIATED BY MATERIAL WHICH MUST CONFORM TO SHIPS PARTS CONTROL CENTER SPECIAL QUALITY CONTROL PROVISIONS AND CERTIFIED FREE FROM MERCURY CONTAMINATION
CENTER HOLE DIAMETER0.484 INCHES MINIMUM AND 0.494 INCHES MAXIMUM IN
TEST DATA DOCUMENT81349-MIL-P-23199 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.).
CROSS-SECTIONAL HEIGHT0.067 INCHES MINIMUM AND 0.073 INCHES MAXIMUM IN
VERIFIED SUBSTITUTES & CROSS-REFERENCES 10
2-014B591-8Interchangeable
interchangeable cross-reference
interchangeable
2-014E540-8Interchangeable
interchangeable cross-reference
interchangeable
2-015 E0540-80Interchangeable
interchangeable cross-reference
interchangeable
NAS1613Interchangeable
interchangeable cross-reference
interchangeable
2-014E515-8Interchangeable
interchangeable cross-reference
interchangeable
NAS1611-014CPInterchangeable
interchangeable cross-reference
interchangeable
LIFECYCLE
StatusACTIVE
AvailabilityOEM and secondary market
RoHS CompliantEAR99Not HAZMAT
Ready to buy 10117183?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 10117183?
10117183 is a O-RING.
What parts can replace 10117183?
There are 10 known substitutes for 10117183: 2-014B591-8, 2-014E540-8, 2-015 E0540-80 and 7 more. Substitute compatibility should be verified for your specific system.
What is the NSN for 10117183?
10117183 is cataloged in the Federal Logistics Information System (FLIS) under NSN 5331-01-268-1249. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Comments (0)
No comments yet. Be the first to share what you know.
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 10117183

✓ Validated with multiple authoritative sources, including Government, OEM, and Certified sources.
PartsTable Design LLC · partstable.com
Last verified: July 2026