PartsTable
Technical Data Sheet
Download PDF

100-300-9-8 — CLIP,SPRING TENSION

✓ Government record, cited
— · ORING SEAL
PRODUCT OVERVIEW

100-300-9-8: CLIP,SPRING TENSION.

The CLIP,SPRING TENSION is a the manufacturer industrial component. Key specifications include width: 0.990 INCHES MINIMUM AND 1.010 INCHES MAXIMUM IN, length: 0.580 INCHES MINIMUM AND 0.600 INCHES MAXIMUM IN, material: COPPER ALLOY 172 OVERALL, hole_diameter: 0.090 INCHES MINIMUM AND 0.096 INCHES MAXIMUM IN, overall_height: 0.670 INCHES MINIMUM AND 0.690 INCHES MAXIMUM IN, mounting_method: UNTHREADED HOLE(S). This part is cataloged in the U.S.

Government catalog under NSN 5340-01-165-3724, indicating validated use in U.S. government and defense logistics supply chains. Available through authorized enterprise resellers and TPM (Third Party Maintenance) channels.

Verify compatibility with your specific system configuration before ordering.

WHERE IT FITS
100-300-9-8
NSN: 5340-01-165-3724
FSC: 5340 — Hardware, Commercial
CAGE: 7RGB6 — ATLEE CORP (USA)
SPECIFICATIONS
width0.990 INCHES MINIMUM AND 1.010 INCHES MAXIMUM IN
length0.580 INCHES MINIMUM AND 0.600 INCHES MAXIMUM IN
materialCOPPER ALLOY 172 OVERALL
hole_diameter0.090 INCHES MINIMUM AND 0.096 INCHES MAXIMUM IN
overall_height0.670 INCHES MINIMUM AND 0.690 INCHES MAXIMUM IN
mounting_methodUNTHREADED HOLE(S)
surface_treatmentCADMIUM AND CHROMATE OVERALL
material_thickness0.014 INCHES MINIMUM AND 0.018 INCHES MAXIMUM IN
loop/holding_dimension0.562 INCHES NOMINAL IN
distance_from_loop_center_to_end0.380 INCHES MINIMUM AND 0.400 INCHES MAXIMUM IN
material_document_and_classificationQQ-C-533,ALLOY 172 FED SPEC SINGLE MATERIAL RESPONSE OVERALL
surface_treatment_document_and_classificationQQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
NSN5340-01-165-3724
COMPONENT DIAGRAM
O-RING / SEAL — MATERIAL DETERMINES APPLICATION ID: — CROSS-SECTION CS: — SPECIFICATION Material: — Durometer: — Temp: — PN: 100-300-9-8 MFR: OEM ⚠ VERIFY BEFORE ORDERING Wrong material = failure. Viton for oil/fuel, EPDM for water/steam, Buna-N for general purpose, Silicone for food-grade. Chemical incompatibility causes swelling, brittleness, or rapid degradation ✓ BROKER TIP Durometer (hardness) affects sealing pressure tolerance. Higher Shore A = harder = higher pressure. Standard durometer is 70A — verify if application requires different hardness PARTSTABLE TECHNICAL DRAWING — NOT TO SCALE
KEY FEATURES
•
LENGTH: 0.580 INCHES MINIMUM AND 0.600 INCHES MAXIMUM IN
•
SURFACE TREATMENT DOCUMENT AND CLASSIFICATION: QQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
•
MOUNTING METHOD: UNTHREADED HOLE(S)
•
MATERIAL DOCUMENT AND CLASSIFICATION: QQ-C-533,ALLOY 172 FED SPEC SINGLE MATERIAL RESPONSE OVERALL
•
LOOP/HOLDING DIMENSION: 0.562 INCHES NOMINAL IN
•
MATERIAL THICKNESS: 0.014 INCHES MINIMUM AND 0.018 INCHES MAXIMUM IN
•
DISTANCE FROM LOOP CENTER TO END: 0.380 INCHES MINIMUM AND 0.400 INCHES MAXIMUM IN
TECHNICAL CHARACTERISTICS
OVERALL HEIGHT0.670 INCHES MINIMUM AND 0.690 INCHES MAXIMUM IN
LENGTH0.580 INCHES MINIMUM AND 0.600 INCHES MAXIMUM IN
SURFACE TREATMENT DOCUMENT AND CLASSIFICATIONQQ-P-416,TYPE 2,CLASS 2 FED SPEC SINGLE TREATMENT RESPONSE OVERALL
MOUNTING METHODUNTHREADED HOLE(S)
MATERIAL DOCUMENT AND CLASSIFICATIONQQ-C-533,ALLOY 172 FED SPEC SINGLE MATERIAL RESPONSE OVERALL
LOOP/HOLDING DIMENSION0.562 INCHES NOMINAL IN
MATERIAL THICKNESS0.014 INCHES MINIMUM AND 0.018 INCHES MAXIMUM IN
DISTANCE FROM LOOP CENTER TO END0.380 INCHES MINIMUM AND 0.400 INCHES MAXIMUM IN
SURFACE TREATMENTCADMIUM AND CHROMATE OVERALL
WIDTH0.990 INCHES MINIMUM AND 1.010 INCHES MAXIMUM IN
SUBSTITUTES & CROSS-REFERENCES 2
16P247-1Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
107306-20Same NSN cross-reference
Same NSN cross-reference
Also cataloged under this NSN
LIFECYCLE
NSN statusActive· U.S. Government catalog
Acquisition advice: Insurance item — stocked against contingency demandNo demilitarization required
Ready to buy 100-300-9-8?
Compare prices from verified sellers on eBay
Buy on eBay →
As an eBay Partner, PartsTable may earn a commission. Your price is not affected.
FREQUENTLY ASKED QUESTIONS
What is 100-300-9-8?
100-300-9-8 is a CLIP,SPRING TENSION.
What parts can replace 100-300-9-8?
There are 2 known substitutes for 100-300-9-8: 16P247-1, 107306-20. Substitute compatibility should be verified for your specific system.
What is the NSN for 100-300-9-8?
100-300-9-8 is cataloged in the U.S. Government catalog under NSN 5340-01-165-3724. This indicates validated use in U.S. government and defense supply chains.
Community Feedback
Leave a Comment
Comments are reviewed before appearing. You will receive an email to verify before your comment appears.

Request a Quote — 100-300-9-8

✓ PartsTable — the parts reference. Every fact cited to its source.
PartsTable Design LLC · partstable.com
U.S. Government catalog: edition PUBLOGDVD v12.0.0 (OCT 2026), edition date 2026-10-01, retrieved 2026-10-18.
PartsTable commercial catalog: edition Unified commercial catalog snapshot through 2026-09-28, edition date not on file, retrieved 2026-09-28.